Holybro Shuriken X1 – AMAZING X-QUAD Flight & Full Review

0 477

What makes the HolyBro Shuriken X1 so amazing? Quite a few things. Starting with the “All in one” pre-flashed Betaflight F3 flight controller, Minim OSD, Pdb, 30Amp BLHeliS Escs, Mr. Steele 5040 HQ Props, and 200mw/600mw Video transmitter. Sony CCD Camera, and 3K carbon fiber X Frame. After all of the good stuff I honestly show you what I think is the not so good stuff on this setup. Mostly good though guys. You are in for a great ride. Would I buy it?

Buy the HolyBro Shuriken with Spectrum Receiver here :

Buy the HolyBro Shuriken with Futuba Receiver here :

Buy the HolyBro Shuriken with FrSky Receiver here :

Extra parts links below :

Extra Shuriken X1 carbon arms here:

Extra Shuriken X1 carbon side plates :

Extra Shuriken X1 2306 2600kv Motors here :

5040 Mr. Steele HQ Propellers :

X1 compatible batteries :

DINOGY 1300mAh 14.8V 4S 65C Li-po Battery :

ZOP Power XT60 Plug 14.8V 4S 1300mAh 45C Battery :

Other Holybro Shuriken Fpv Quads :

RTF Holybro Shuiken 250 :

Holybro Shuriken 180 with DSMX Spectrum Receiver :

Video contents:
– Flight Test and commentary
– Introduction and What’s in the box?
– X1 overview
– All in one flight controller overview
– LED and camera setup
– Betaflight setup help
– Final Thoughts

Manufacturer Specs :

Main Features:
– Full 3K Carbon Fiber
– Nickel-plated 12.9 screws
– Anti-slip black anodized spacers
– Flight controller, OSD, PDB, video transmitter and voltage / current sensor are all integrated, which makes an integral structure with a much lower center of mass
– 5.8GHz 40-channel 200mW / 600mW switchable FPV transmitter with built-in push button and LED channel display
– High-quality SpiroNet antenna
– Integrated MWOSD ( preloaded with firmware V1.5 )
– 600TVL PAL camera with 2.5mm lens, 1/3 inch Super HAD II CCD
– Compatible with SBus, DSMX, and PPM receivers
– 3-colour LED board controlled by LED strip signal
– Two mounting positions for the FPV camera: one for 0 to 40 degree angle of view, the other for 35 to 70 degree angle of view
– Includes TPU GoPro Session mount ( 35 degree angle of view )
– BetaFlight pre-loaded, CleanFlight ready

– 32-bit F3 flight controller
– MPU6050 gyroscope / accelerometer
– ATmega328P with Arduino boot loader ( minimOSD )
– MAX7456 monochrome on-screen display ( minimOSD )
– FTDI cable compatible pinout ( minimOSD )
– Oneshot125 BLheli-S 30A ESCs ( 40A burst current )
– T-MOTOR 2305 2600KV motors
– Compact size and 200mm diagonal length for 5 inch propellers
– Input voltage: 7 – 42V
– Filtered voltage output 5.2V 2A
– Weight: 343g ( excluding battery )
– Remote control distance: 300 meters

Racing Quadcopter Parameters:
Wheelbase: 200mm
Video Resolution: 600TVL
Video Standards: PAL
Dimension and Weight
Product weight: 0.343 kg
Package weight: 0.800 kg
Product size (L x W x H): 26.00 x 22.00 x 8.00 cm / 10.24 x 8.66 x 3.15 inches
Package size (L x W x H): 32.00 x 31.00 x 12.00 cm / 12.6 x 12.2 x 4.72 inches

Package Contents: 1 x Shuriken X1, 1 x 5.8G Mushroom Antenna, 1 x Gopro Session Protector ( TPU 3D Print ), 1 x Camera Strap, 2 x Zip Tie, 1 x Cable

Drone Camps Community :

Subscribe for weekly new
drones, honest reviews, prototypes,
tutorials, and tech gadgets. – Mon – Fri

Business Inquires:
To get your product reviewed please email:
drone camps @ gmail. com

Drone Camps RC
Tel: 912-441-1412

LIKE us on Facebook
FOLLOW on Instagram: Drone Camps RC


You might also like More from author

Leave A Reply

Your email address will not be published.